Chemical versus Electrochemical Synthesis of Carbon Nano‐onion/Polypyrrole Composites for Supercapacitor Electrodes

The development of high‐surface‐area carbon electrodes with a defined pore size distribution and the incorporation of pseudo‐active materials to optimize the overall capacitance and conductivity without destroying the stability are at present important research areas. Composite electrodes of carbon nano‐onions (CNOs) and polypyrrole (Ppy) were fabricated to improve the specific capacitance of a supercapacitor. The carbon nanostructures were uniformly coated with Ppy by chemical polymerization or by electrochemical potentiostatic deposition to form homogenous composites or bilayers. The materials were characterized by transmission‐ and scanning electron microscopy, differential thermogravimetric analyses, FTIR spectroscopy, piezoelectric microgravimetry, and cyclic voltammetry. The composites show higher mechanical and electrochemical stabilities, with high specific capacitances of up to about 800 F g^?1 for the CNOs/SDS/Ppy composites (chemical synthesis) and about 1300 F g^?1 for the CNOs/Ppy bilayer (electrochemical deposition).     

The Reductive Dehydration of Cellulose by Solid/Gas Reaction with TiCl4 at Low Temperature: A Cheap,Simple, and Green Process for Preparing Anatase Nanoplates and TiO2/C Composites

Metal oxides and metal oxide/carbon composites are entering the development of new technologies and should therefore to be prepared by sustainable chemistry processes. Therefore, a new aspect of the reactivity of cellulose is presented through its solid/gas reaction with vapour of titanium(IV) chloride in anhydrous conditions at low temperature (80 °C). This reaction leads to two transformations both for cellulose and titanium(IV) chloride. A reductive dehydration of cellulose is seen at the lowest temperature ever reported and results in the formation of a carbonaceous fibrous solid as the only carbon‐containing product. Simultaneously, the in situ generation of water leads to the formation of titanium dioxide with an unexpected nanoplate morphology (ca. 50 nm thickness) and a high photocatalytic activity. We present the evidence showing the evolution of the cellulose and the TiO₂ nanostructure formation, along with its photocatalytic activity. This low‐temperature process avoids any other reagents and is among the greenest processes for the preparation of anatase and also for TiO₂/carbon composites. The anisotropic morphology of TiO₂ questions the role of the cellulose on the growing process of these nanoparticles.     

A Self‐Assembled Superhydrophobic Electrospun Carbon–Silica Nanofiber Sponge for Selective Removal and Recovery of Oils and Organic Solvents

An oil spill needs timely cleanup before it spreads and poses serious environmental threat to the polluted area. This always requires the cleanup techniques to be efficient and cost‐effective. In this work, a lightweight and compressible sponge made of carbon–silica nanofibers is derived from electrospinning nanotechnology that is low‐cost, versatile, and readily scalable. The fabricated sponge has high porosity (>99 %) and displays ultra‐hydrophobicity and superoleophilicity, thus making it a suitable material as an oil adsorbent. Owing to its high porosity and low density, the sponge is capable of adsorbing oil up to 140 times its own weight with its sorption rate showing solution viscosity dependence. Furthermore, sponge regeneration and oil recovery are feasible by using either cyclic distillation or mechanical squeezing.     

Highly Selective Zeolite Topologies for Flue Gas Separation

The separation of carbon dioxide from flue gas is essential for the reduction of greenhouse gas emissions. In adsorptive methods, the challenge lies in the choice of suitable porous materials. Among all zeolite topologies, a number of adsorbents with pore dimensions in the range of the guest molecules were identified to allow an excellent separation by diffusion, and MRE and AFO zeolite topologies appear to be the best candidates based on equilibrium adsorption. Also, it was found that the behavior of this gas mixture in DFT and APD zeolites differed from the normal behavior.     

UHMWPE纤维的超临界CO_2辅助渗透预处理研究

利用Minitab软件设计实验,以超高分子量聚乙烯纤维(UHMWPE)为原料,研究了在不同的超临界CO_2流体状态下,处理压力、温度和时间等因素对三羟甲基丙烷三甲基丙烯酸酯(TMPTMA)渗入率的影响,确定了最佳因素设置范围;通过单因子实验优化了超临界CO_2处理工艺,并对经过电子束辐照的UHMWPE纤维凝胶含量和蠕变率进行了测试。研究结果表明:处理温度对TMPTMA的渗入率影响最大,其次为压力,时间的影响最小,确定了最优工艺条件为处理压力25MPa,温度80℃,时间30min;TMPTMA渗入率越高,电子束辐照后UHMWPE纤维的增感辐照交联效应和抗蠕变效果越好。     

硼原子掺杂对碳纳米管吸附Ne原子影响的第一性原理计算

采用基于第一性原理的密度泛函理论（DFT）和局域密度近似（LDA）方法，优化计算得到碳纳米管（CNT），硼原子取代碳原子及其吸附氖原子前后系统的几何结构，能量，电子能带和态密度。结果显示，碳纳米管的能带结构与石墨的层状几何结构相似，能量的变化只在kz=0和kz=0.5平面之间沿着c轴方向出现。B原子取代C原子使价带和导带分别分裂为两个和三个能带。对Ne原子的吸附使价带能量沿着c轴方向升高并导致Fermi面附近的态密度下降。Ne原子的吸附在谷位H最稳定，顶位A其次。C-C间σ键的弯曲使Ne原子吸附在桥位b1比桥位b2处更为稳定。Ne原子在管外的吸附均为放热过程，而管内则为吸热过程。结构分析表明Ne原子对C原子有排斥作用，对B原子却具有吸引作用。B原子取代C原子的位置略凸出于CNT的管壁之外，使Ne原子的吸附能增加。     

Regioselective Alkylative Carboxylation of Allenamides with Carbon Dioxide and Dialkylzinc Reagents Catalyzed by an N‐Heterocyclic Carbene–Copper Complex

The alkylative carboxylation of allenamide catalyzed by an N‐heterocyclic carbene (NHC)–copper(I) complex [(IPr)CuCl] with CO₂ and dialkylzinc reagents was investigated. The reaction of allenamides with dialkylzinc reagents (1.5 equiv) and CO₂ (1 atm.) proceeded smoothly in the presence of a catalytic quantity of [(IPr)CuCl] to afford (Z)‐α,β‐dehydro‐β‐amino acid esters in good yields. The reaction is regioselective, with the alkyl group introduced onto the less hindered γ‐carbon, and the carboxyl group introduced onto the β‐carbon atom of the allenamides. The first step of the reaction was alkylative zincation of the allenamides to give an alkenylzinc intermediate followed by nucleophilic addition to CO₂. A variety of cyclic and acyclic allenamides were found to be applicable to this transformation. Dialkylzinc reagents bearing β‐hydrogen atoms, such as Et₂Zn or Bu₂Zn, also gave the corresponding alkylative carboxylation products without β‐hydride elimination. The present methodology provides an easy route to alkyl‐substituted α,β‐dehydro‐β‐amino acid ester derivatives under mild reaction conditions with high regio‐ and stereoselectivtiy.     

Na2S–Carbon Nanotube Fabric Electrodes for Room‐Temperature Sodium–Sulfur Batteries

A unique sodium sulfide (Na₂S) cathode is developed, which will allow the use of sodium‐free anodes for room‐temperature sodium–sulfur (Na–S) batteries. To overcome the “inert” nature of the Na₂S, a special cathode structure is developed by spreading the multi‐walled carbon nanotube (MWCNT)‐wrapped Na₂S particles onto MWCNT fabrics. Spectroscopic and electrochemical analyses reveal a series of polysulfide intermediates involved in the charge/discharge of the cell. The Na–S battery prepared in full discharge state with the Na₂S/MWCNT cathode provides a remarkable capacity of 500 A h kg^?1 (based on sulfur mass) after 50 cycles.     

One‐Pot Synthesis of Pomegranate‐Structured Fe3O4/Carbon Nanospheres‐Doped Graphene Aerogel for High‐Rate Lithium Ion Batteries

A unique hierarchically nanostructured composite of iron oxide/carbon (Fe₃O₄/C) nanospheres‐doped three‐dimensional (3D) graphene aerogel has been fabricated by a one‐pot hydrothermal strategy. In this novel nanostructured composite aerogel, uniform Fe₃O₄ nanocrystals (5–10 nm) are individually embedded in carbon nanospheres (ca. 50 nm) forming a pomegranate‐like structure. The carbon matrix suppresses the aggregation of Fe₃O₄ nanocrystals, avoids direct exposure of the encapsulated Fe₃O₄ to the electrolyte, and buffers the volume expansion. Meanwhile, the interconnected 3D graphene aerogel further serves to reinforce the structure of the Fe₃O₄/C nanospheres and enhances the electrical conductivity of the overall electrode. Therefore, the carbon matrix and the interconnected graphene network entrap the Fe₃O₄ nanocrystals such that their electrochemical function is retained even after fracture. This novel hierarchical aerogel structure delivers a long‐term stability of 634 mA h g^?1 over 1000 cycles at a high current density of 6 A g^?1 (7 C), and an excellent rate capability of 413 mA h g^?1 at 10 A g^?1 (11 C), thus exhibiting great potential as an anode composite structure for durable high‐rate lithium‐ion batteries.     

Insights into the Cascade Reaction of CO and Heteroallenes Mediated by Dinitrogen Hafnocene Complexes: The Indirect Effect of Nitride's Nucleophilicity

A DFT mechanistic exploration of the reactivity of the dinitrogen hafnocene complex, [{(η⁵‐C₅H₂‐1,2,4‐Me₃)₂Hf}₂(μ₂‐N₂)], towards mixtures of CO/CO₂ and CO/OCNtBu is reported. The crucial role of the nitride intermediate is highlighted, as well as the importance of the bridging mode of the cyanate ligand between the two Hf metal atoms throughout the process. Interestingly, the CO₂ addition to the nitride intermediate occurs through an outer‐sphere transition state, whereas the addition of the heteroallene is governed by the steric congestion imposed by cyclopentadienyl ligands.